Items 1 to 3 of 9 total

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3

Be My Valentine Card

09/02/2018 11:49

  1. Cut red card 120mm sq. mat onto slightly larger black card square and then at an angle onto the front of a 6x6 white card base.
  2. Using black and red memento inks, stamp the ‘be my valentine’ sentiment and arrow motif onto smooth white card to create a frame.  Aiming for approx. 100mm square panel.
  3. Stamp the large envelope and the hearts cluster into the centre of the frame using black memento ink.  Stamp the envelope again onto a scrap of white card.  Colour the hearts with a red alcohol marker and outline hearts and envelope with a light grey marker. Extra details can be added with a white pen if desired.
  4. Trim stamped panel to approx. 100mm sq. and mat onto slightly larger square of black card using d/s tape.  Attach to card front at an angle using 3D foam pads. 
  5. To finish, cut out previously coloured envelope and add in place over stamped envelope on card front, use 3D foam pads to raise it.
 
See all of Angela's posts and her bio Here

Sweet Valentines Stamp Set

KP-LOVE

Gotta Have Memento Ink Pads

MDIP100-009

Brights Pen Set

SPECN-BRIGHTS24

Dual Tip Blender Pen

GRAPHBLEND

"I am a passionate papercrafter. I have also had my cards and projects published in magazines and was absolutely thrilled to be crowned Cardmaker of the Year 2016 by my favourite magazines! I have been 'crafting' for quite a few years now and always made my own greetings cards for family and friends. I do love playing and experimenting with all sorts of crafty materials. Papercrafting has always been my passion"

 

Posted in Cards with Stamping Angela Dodson By Angela Dodson

  1. Take the 5 x7 ribbon thread card blank and position with thread holes along bottom.  Cut a length of the ribbon slightly longer than the card and thread through the ribbon holes.  Add a little adhesive under the ribbon at the left and right sides to hold ribbon in place. Trim ends using scissors.
  2. Cut white card approx. 16cm x 9cm and mat onto green card approx. 17cm x 10cm using d/s tape.  Mat panel onto card front using d/s tape.
  3. Using the Stocking die, die cut 2 green stockings and 1 red stocking.  Die cut the shape again from silver card and use to paper piece the stockings (or leave as cut outs if you prefer)
  4. Cut 3 squares of white card approx. 4cm x 4cm and mat 2 onto red card squares (5cm) and 1 onto a green square.  Position squares as diamonds and adhere a stocking to each one.
  5. Adhere the 2 red squares to card front, 1 at left and 1 at right, a ruler placed across the front will help you line up the points of each square.  Finally add the green square using 3D foam pads, positon slightly lower and so it overlaps the red squares.
  6. To finish, decorate each stocking with a red or green sequin, top with a red or green adhesive gem and add a further gem to design on centre of stocking.
 
See all of Angela's posts and her bio Here

Hobbybase Club Box November 2017

Subscribe For Future Editions Here:

www.hobbybase.club

  Plus the following basics:
  • White Card
  • Red, Green & Silver Mirror Card
  • Adhesive Gems

"I am a passionate papercrafter. I have also had my cards and projects published in magazines and was absolutely thrilled to be crowned Cardmaker of the Year 2016 by my favourite magazines! I have been 'crafting' for quite a few years now and always made my own greetings cards for family and friends. I do love playing and experimenting with all sorts of crafty materials. Papercrafting has always been my passion"

 

Posted in Club Projects Angela Dodson By Angela Dodson

  1. Take the Gatefold Card blank and cover inside with 14.5cm square of pattern paper. Cut 4 14.5cm x 7cm pieces of pattern paper to cover the 2 inside panels and 2 outside panels, adhering paper with d/s tape or runner.
  2. Cut pattern paper approx. 9.5cm x 5.75cm and mat onto a slightly larger piece of white card using d/s tape.  Position this panel in centre of card where it spans both left and right panels equally.  Add adhesive only to the back of the half that will adhere to left hand side panel. Left panel will open with the sentiment attached.
  3. Die cut the Merry Christmas sentiment from gold card (or from pattern paper in the box) Adhere sentiment onto a piece of white card using the glue pen.  When dry trim down to approx. 8.5cm x 4.5cm and mount onto centre panel of card using 3D foam pads to raise it a little.
  4. Cut 2 large and 2 small pennant shapes from pattern paper (easy to ‘fish tail’ ends with scissors if you don’t have dies) mat each pennant onto slightly larger white card and adhere to card front as shown, using 3D foam pads to raise them.
  5. Decorate inside panel with a circle or square of contrasting pattern paper. Optional extra:  add 2 little deer using the glue pen.  The deer can be found on the Merry Christmas die, simply die cut, trim them off and glue them in place.
  6. To finish, add gold sequins along each pennant on the card front using a clear drying glue.  Your sentiment can be written on the back of the card or cut a small panel of white card and attach to the back or the inside.
 
See all of Angela's posts and her bio Here

Hobbybase Club Box November 2017

Subscribe For Future Editions Here:

www.hobbybase.club

  Plus the following basics:
  • White Card
  • Gold Card
  • Gold Sequins

"I am a passionate papercrafter. I have also had my cards and projects published in magazines and was absolutely thrilled to be crowned Cardmaker of the Year 2016 by my favourite magazines! I have been 'crafting' for quite a few years now and always made my own greetings cards for family and friends. I do love playing and experimenting with all sorts of crafty materials. Papercrafting has always been my passion"

 

Posted in Club Projects Angela Dodson By Angela Dodson

Items 1 to 3 of 9 total

Set Ascending Direction
per page
Page:
  1. 1
  2. 2
  3. 3